File: Blinky_ADCDownload   Add to favorates  [Vote: very good!  5  4  3  2  1 Vote: very bad!]
  Directory: SCM
  Dev tools: C-C++
  File size: 732 KB
  Update: 2012-07-31
  Downloads: 1
  Uploader: qqhrqidian
 Describe: The Blinky project is a simple program for the STM32F407Z microcontroller using STM STM3240G-EVAL Evaluation Board, compliant to Cortex Microcontroller Software Interface Standard (CMSIS v2.0). Example functionality: - Clock Settings: - XTAL = 25.00 MHz - SYSCLK = 168.00 MHz - Sys Timer is used in interrupt mode - LED blink with speed depending on potentiometer position - colour LCD display shows init message and bargraph depending on potentiometer position - AD settings: 12 bit resolution - AD value is output onto serial port UART4 UART4 settings: 115200 baud, 8 data bits, no parity, 1 stop bit The Blinky program is available in different targets: STM32F407 Flash: runs from Internal Flash located on chip (used for production or target debugging) STM32F407 RAM: runs from Internal RAM located on chip (may be used for target d
File list(Click to check if it's the file you need, and recomment it at the bottom):
  Blinky_ADC\Abstract.txt
  ..........\ADC.c
  ..........\ADC.h
  ..........\Blinky.c
  ..........\Blinky.uvgui
  ..........\Blinky.uvgui.HYX
  ..........\Blinky.uvgui.xdn
  ..........\Blinky.uvgui_HYX.bak
  ..........\Blinky.uvgui_xdn.bak
  ..........\Blinky.uvopt
  ..........\Blinky.uvproj
  ..........\Blinky_STM32F407 Flash.dep
  ..........\Blinky_uvopt.bak
  ..........\Blinky_uvproj.bak
  ..........\Dbg_RAM.ini
  ..........\Font_16x24_h.h
  ..........\Font_6x8_h.h
  ..........\GLCD.h
  ..........\GLCD_16bitIF_STM32F4xx.c
  ..........\IRQ.c
  ..........\JLinkLog.txt
  ..........\JLinkSettings.ini
  ..........\Retarget.c
  ..........\Serial.c
  ..........\startup_stm32f4xx.s
  ..........\system_stm32f4xx.c
  ..........\Flash\adc.crf
  ..........\.....\adc.d
  ..........\.....\adc.o
  ..........\.....\Blinky.axf
  ..........\.....\blinky.crf
  ..........\.....\blinky.d
  ..........\.....\Blinky.htm
  ..........\.....\Blinky.lnp
  ..........\.....\Blinky.map
  ..........\.....\blinky.o
  ..........\.....\Blinky.plg
  ..........\.....\Blinky.sct
  ..........\.....\Blinky.tra
  ..........\.....\blinky.__i
  ..........\.....\ExtDll.iex
  ..........\.....\glcd_16bitif_stm32f4xx.crf
  ..........\.....\glcd_16bitif_stm32f4xx.d
  ..........\.....\glcd_16bitif_stm32f4xx.o
  ..........\.....\glcd_16bitif_stm32f4xx.__i
  ..........\.....\irq.crf
  ..........\.....\irq.d
  ..........\.....\irq.o
  ..........\.....\retarget.crf
  ..........\.....\retarget.d
  ..........\.....\retarget.o
  ..........\.....\serial.crf
  ..........\.....\serial.d
  ..........\.....\serial.o
  ..........\.....\startup_stm32f4xx.d
  ..........\.....\startup_stm32f4xx.lst
  ..........\.....\startup_stm32f4xx.o
  ..........\.....\system_stm32f4xx.crf
  ..........\.....\system_stm32f4xx.d
  ..........\.....\system_stm32f4xx.o
  ..........\Flash
  Blinky_ADC
 Search in more than 1820000 codes/documents:
 [stepper-motor.rar] - atmega88 drive stepper motor, K3, K4 buttons control acceleration and deceleration, K1, K2 control switch and rotating, and in the 5110 liquid crystal