陈呐尼 2019-04-16 19:55:15
Description: CC2530 basic control LED water lamp. Light-emitting diode (LED) is a kind of diode, which has the characteristics of two-stage transistor unidirectional conductivity, that is, only under the positive voltage (diode positive, negative) can light-emitting be conducted. P1.0 pin connects the negative pole of light emitting diode (D1), so P1.0 pin output low level D1 bright, P1.0 pin output high level D1 extinguished, D2, D3 the same.
Plat: C# | Size: 221KB | Downloads: 0
林c 2019-04-11 15:53:05
Description: LED Pipeline Lamp Program, Test Program Based on STM32 Single Chip Microcomputer, Novice Learning
Plat: C/C++ | Size: 319KB | Downloads: 0
梦恋星空 2019-04-06 14:37:52
Description: This is differentiated by the scope of application of Microcontrollers. For example, the 80C51 general-purpose single-chip microcomputer is not designed for a special purpose; the special-purpose single-chip microcomputer is designed and manufactured for a class of products or even a certain product, for example, to meet the requirements of the electronic thermometer, integrate the ADC interface and other functions on the chip. Temperature measurement control circuit
Plat: C/C++ | Size: 634KB | Downloads: 0
噼里啪啦01 2019-04-05 23:43:53
Description: The experience of Arduino design, which has been summarized through thousands of efforts, is for reference only.
Plat: C/C++ | Size: 7145KB | Downloads: 0
321964233 2019-04-04 12:51:47
Description: Controlling LED Scintillation through Serial Port
Plat: C/C++ | Size: 21KB | Downloads: 0
llq000 2019-04-03 00:37:40
Description: FPGA project, describes a simple control of LED lamp on FPGA development board
Plat: Quartus II | Size: 1KB | Downloads: 0
zjsxhwl 2019-04-01 13:42:30
Description: It took me a long time to write this, using CodeWarrior 6.2. Using FREESCALE MCU, MC9S08DZ60. Written by EXPERT. There are led, AD, SPI digital tube (PE).
Plat: C/C++ | Size: 225KB | Downloads: 0
fatemieh 2019-03-31 15:10:40
Description: PLC THERNET MODBUS AND >>>
Plat: PLC | Size: 6309KB | Downloads: 0
pohahah 2019-03-28 07:33:03
Description: adfvff f fdfs f dvdsz dz vdzsvd hdfdgvaz
Plat: HTML | Size: 87KB | Downloads: 0
bobboo2313 2019-03-27 07:33:08
Description: A tiny RGBLED library I wrote. Someone might find this useful. It contains HSB to RGB code that I wrote (and am proud of)
Plat: Arduino | Size: 16387KB | Downloads: 0
Dman 2019-03-27 04:51:03
Description: In this project, I toggle the LED using the MCC configurator.
Plat: C/C++ | Size: 96KB | Downloads: 0
吼吼吼1 2019-03-26 09:19:31
Description: Programming and Simulation of pattern flow lamp with 51 single chip computer
Plat: C/C++ | Size: 54KB | Downloads: 0
吼吼吼1 2019-03-26 09:11:08
Description: Realize the control of the flow lamp from left to right
Plat: C/C++ | Size: 51KB | Downloads: 0
Usagi_ 2019-03-23 22:34:48
Description: In fact, the LED pipeline lamp is a minimal application system of a single chip computer with eight light-emitting diodes, that is, a single single chip computer composed of light-emitting diode, crystal oscillator, reset, power supply circuit and necessary software.
Plat: C51 | Size: 852KB | Downloads: 0
lmoyun 2019-03-23 09:28:33
Description: LED water lamp. Horse lamp, dazzling LED light effect.
Plat: C/C++ | Size: 17KB | Downloads: 0
MastNaeem 2019-03-21 01:03:41
Description: Led firmware useful for v59 board
Plat: Others | Size: 2807KB | Downloads: 0
gxq1233 2019-03-20 07:57:52
Description: STC8A, LED and other lighting procedures
Plat: C/C++ | Size: 15KB | Downloads: 2
ThreeJ 2019-03-19 18:23:02
Description: The test file of PFGA LED lamp is very useful.
Plat: Quartus II | Size: 2922KB | Downloads: 0
hyg7991 2019-03-18 01:15:31
Description: Can make LED lamp flicker regularly
Plat: C/C++ | Size: 6245KB | Downloads: 0
fannakh 2019-03-15 23:52:30
Description: ne555 simulation in isis proteus
Plat: C/C++ | Size: 271KB | Downloads: 0
hbzjt2012 2019-03-04 12:24:45
Description: Proteus simulation and LCD12864 source program
Plat: C/C++ | Size: 1440KB | Downloads: 0
Xugt 2019-03-01 16:55:33
Description: Based on the two-way synchronous communication of uCOSII real-time system, the message is sent after the key count, waiting for the serial port to send a complete reply, ask and answer, to ensure the success of each communication, no omission!
Plat: C/C++ | Size: 7128KB | Downloads: 0
开发163 2019-02-24 17:32:56
Description: The module consists of four monochrome 8*8 LED lattices. The module size is 64mm*64mm PCB bottom plate thickness.1.6mm, multiple modules can achieve seamless cascade.
The hardware uses two 74HC138 cascades to expand four address lines to achieve one-sixteenth sweep. The data lines use 74HC595 chip with SPI interface. Two 74HC595 cascades are used to realize 16-bit data output. In addition, in order to avoid input signal distortion caused by cascade of multiple modules, this module specially adds 74HC245 buffer chip to the input stage, sixteen 8550 transistors are used.
Plat: C# | Size: 37KB | Downloads: 0
灯11111111 2019-02-23 16:56:01
Description: Intelligent management of desk lamp can be realized by adjusting lighting brightness manually or automatically in different ways.
Plat: C/C++ | Size: 11782KB | Downloads: 0
S王 2019-02-13 10:37:57
Description: LED Send wdwdqwdwqdqw
Plat: C# | Size: 349KB | Downloads: 0
Johnney Juan 2019-02-04 12:45:20
Description: Entertaining diversions initialization and testing, zhejiang university robot
Plat: C/C++ | Size: 21KB | Downloads: 0
dluf1991 2019-01-31 09:04:53
Description: STM32F103VET6 development entry, suitable for STM32F1 series, simple control of LED to achieve respiratory lamp effect. Developing with MDK
Plat: C/C++ | Size: 905KB | Downloads: 0
bundy 2019-01-31 06:46:59
Description: LED Blinky for amr-gcc.
Plat: C/C++ | Size: 56KB | Downloads: 0
蓝色祥龙 2019-01-29 22:10:07
Description: The program is changed to VB motor control upper computer program to monitor and control motor rotation.
1. Connect the serial port line, and connect the indicator lamp to the P0 port of the single chip computer.
2. The port in PC software is 3, so it is necessary to change the port in device manager to 3.
3. Burn and write the program of the lower computer to the single chip computer, crystal oscillator 12MHZ
4. Select COM3 - Open the serial port and control it by the eight buttons above.
On and off of D11-D18 lamp on single chip computer
Plat: VBA | Size: 268KB | Downloads: 0